![]() ![]() Saitek Multi, Radio and Switch Panels are supported (updated for MSFS events and 8.The app includes virtual flight instruments that can be dragged to one of your monitors or accessed using the web browser on your phone or tablet when they are in your LAN or WiFi.A "Mouse Yoke" mode is included, for those simulators that don't have it by default (=MSFS).Every axis and event of the simulator can be assigned and used.Controller axis can be calibrated, response curves are available.This enables you to assign the same controllers in a different way for each aircraft that you fly. It does NOT deliver direct-to-use configurations for airplanes or helicopters. Controller profiles are loaded and saved individually to your aircraft in the simulator. The X-Touch Gauge for Axis and Ohs is a framework, that helps you programming the Behringer X-Touch Mini Midi Controller to use as an input device for Microsoft Flight Simulator 2020 using AAO (Axis and Ohs) Software.There are additional (free) "Bridge" apps available for more exotic hardware (currently availbale: Elgato StreamDeck, VRI MCP Combo II Boeing, "Knobster", Arduino, HID-Devices) on the DOWNLOADS page The app supports native Windows USB Game Controller devices, MIDI devices and the Windows 10 Voice Recognition system. XTouch Mini.jpg Inside.jpg Converter.Axis and Ohs is an external application that replaces the controller (=yokes, joysticks, etc) logic in (*) HobbyTronics have improved this product. I hope that I don't need this capability but it's in the mixer's gig-bag just in case. So I have achieved what I set out to do: I can take control of the basic mute and fader functions of the XR if my tablet and/or network fail. ![]() This is another way to get the faders synchronized without loading a snapshot. ![]() As another handy shortcut, I use the encoder press functions to set default fader levels for their respective channels/buses. The quick solution to this is to load an XR snapshot which gives instant synchronization so I programmed one of the spare XTouch buttons to load my default snapshot. When first turned on, though, the XTouch does not reflect the state of the XR. The encoder LED rings and mute LEDs follow the XR state when controlled by both the MIDI board and the normal network UI. Using the XTouch Editor, I have programmed eight encoders and eight buttons to control the faders and mutes for the critical channels and buses using the published MIDI messages. It used to control vMix but I'm trying something new and work. The converter and controller only draw about 100mA so I can run it for over twelve hours from a 2000mAh phone powerbank if there is no convenient power outlet or spare USB-A port. I bring you along with my while I figure out how to make the xTouch Mini control the ATEM Mini. ![]() These two boards are mounted in a small box along with a connector for 5Vdc power. I took the low-cost route by using HobbyTronics USB Host Mini (preloaded with MIDI firmware) plus a HobbyTronics MIDI Breakout. The HobbyTronics MIDI USB-DIN Converter is much lower cost but looks a little fragile (*) so would need to be repackaged for life on the road. Unfortunately, I dont have documentation from BMD about specific MIDI commands that it recognizes, though Ive. The goal is to design a map for yourself that is most compatible with each system. The Kenton MIDI USB Host would work but is rather expensive. It does have some support for MIDI control, for instance I was able to adjust panning and faders with this layout. This can be resolved, though, with a USB/DIN MIDI converter. The XTouch Mini, in common with most small and reasonably priced controllers, is a USB MIDI device and the XR12 requires DIN MIDI. I have achieved this using the XTouch Mini. Tutorial on setting up a Behringer X Touch Mini with Black Magic ATEM Software Controller. I did want the controller to have feedback for mute states and fader levels. ATEM Black Magic MIDI Controller Set Up Tutorial. I have long thought it would be good to have basic control via MIDI in case I lost my normal user interface but I did not want a large and/or expensive controller. I carry a spare 7" tablet, backup access point and an OTG adaptor for wired Ethernet but I don't have much time for trouble-shooting. The only challenge with this job is that I get very little time for get-in and get-out so any problems in setting up could be disastrous. I have a regular small sound job that I handle with an XR12 controlled from a 10" Android tablet running Mixing Station X Air Pro. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |